تلفن تماس : 66764145-021

فلایت کنترل CC3D Revoulation

270,000 تومان

فلایت کنترلر  CC3D REV 10DOF

وزن فلایت کنترلر:15g

ابعاد فلایت کنترلر:40mmx40mmx10mm

در انبار موجود نمی باشد

 

اتوپایلوت Openpilot CC3d Revolution  یکی از پرفروشترین فلایت کنترلهای حرفه ای معروف سایز متوسط موجود در بازار جهانی است. با داشتن جایرو سه محوره و سنسور شتاب سنج سه محوره و قطب نمای ۳ محوره و سنسور فشارسنج داخلی عملا یک کنترلر فوق حرفه ای را در اختیار خواهید داشت

این فلایت کنترلر بر خلاف نسخه های معمولی و عادی خود ۱۰DOF بوده و همچنین با اتصال GPS به آن میتوان حالت RTH یا همان بازگشت به خانه را نیز فعال کرد که در بقیه ورژن های معمولی این قابلیت را در اختیار نداشتیم

با تنظیمات بسیار آسان در کمترین وقت ممکن قادر به راه اندازی مولتی روتور خود به صورت کواد یا هگزا روتور با ترکیب پلاس خواهید بود. همچنین پورت میکرو USB بر روی این فلایت کنترل این توانایی را به آن میدهد تا به کامپیوتر متصل گشته و برنامه ریزی یا آپگرید نرم افزاری آن را به راحتی انجام دهید .

MORE DETAILS:

CPU
CPU is the STM32F405RGT6 chip, with ARM Cortex-M4 core at 210MIPS, FPU, and saturation arithmetics DSP functions.
The chip features a range of built-in hardware modules that can bo programmed once and function independently, requiring little to no CPU overhead. These include 14x multichanel timers, 3x synchronous-sampling ADC serving up to 24 channels, 2x DAC, matrix memory controller with 16-stream DMA, and other. Communication modules include USB2.0, 3x I2C, 3x SPI, 4x USART, 2x CAN and SIDO. All these modules can be configured for accessing the chip pins using a flexible switch matrix, or disabled to save power.
It even contains a real time hardware calendar if you want a wake up flight.
The software and settings are loaded through USB connector and no-hassle update function in the GCS (Ground Control Station).
MPU: 6000
Modem The board features a built-in 433MHz OPLink Modem.
Dimensions OpenPilot products use the standard OpenPilot footprint, and hence has the same dimensions and mounting holes as the OpenPilot CC. CC3D, Revo, GPS, OSD and PipX boards.
Ports
Servo 1-6: These are the PWM outputs that go to servos or electronic speed controllers (ESCs).  Power for the flight controller is typically supplied through these headers from only one of the ESCs, but in most cases, all the servo wires can be left connected. Cutting the pin from servo wires is highly discouraged.  If you feel you must disconnect three of the hot wires, use some shrink tube or electrical tape to insulate the removed pin (you may need that positive voltage at a later date!).  The positive (Vcc) and negative (Gnd) pins are indicated on this diagram and the board. In rare cases, you may need to also disconnect the ground pin if your ESCs are creating ground loop problems (indicated by a general weirdness in setup).  (see the CopterControl – CC3D -Atom Hardware Setup page, Power section, for instructions on how to remove and insulate the extra pins)
Servo output pin layout
Outside –> ground
Middle –> 5V – 8.4V
Inside –> signal
Flexi-IO Port The receiver port can act as an input or output port depending on the configuration which is set in the Hardware Settings. Configuring the receiver port as an output port allows the user to assign more output channels then the 6 standard servo outputs.
PWM -vs- PPM Recievers Please be aware that not all receivers can be configured to use a PPM output. It is the user’s responsibility to research this feature in regards to the desired receiver they wish to use for PPM and ensure it can be used as such. Many hours of frustration can occur while trying to troubleshoot why you can’t get your radio to connect to the board with PPM if using a receiver than isn’t designed with that feature! Simply make sure the receiver can do it before trying to set it up that way.
MainPort JST-SH 4-pin.
This is a serial USART whose baud rate can be adjusted through the GCS. Optionally, Futaba S.Bus receiver, Spektrum/JR satellite receiver or GPS can be mapped to the MainPort. Default configuration is Telemetry for connecting an RF modem.
FlexiPort JST-SH 4-pin.
The function of this port also depends on the configuration and can be configured for I2C or Serial. The default configuration doesn’t use this port, but it can be used for Telemetry, GPS, Spektrum satellite receivers (all working), and other I2C peripherals (under development).
RF Socket Antenna connection socket for on-board OPLink modem.
Pwr Sen/Sonar Port JST-SH 4-pin.
This port can be configured to accommodate an Autopilot current sensor and a low cost Sonar sensor such as the HC-SR04. It can also be used as a general purpose input/output port or as a one or two channel analog input port.

Image result for cc3d revolution

#فلایت کنترلر #کنترلر پرواز # خلبان خودکار # cc3d REV#flight controller #autopilot#اتوپایلوت # raceflight # openpilot

هیچ دیدگاهی برای این محصول نوشته نشده است.

اولین نفری باشید که دیدگاهی را ارسال می کنید برای “فلایت کنترل CC3D Revoulation”

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

بروزرسانی …
  • سبد خرید شما خالی است.